17.7.3.2.4.3* For sloping ceilings

17.7.3.2.4.3* For sloping ceilings with beams running parallel
up slope, the following shall apply:
(1) Spot-type detector(s) shall be located on the ceiling within
beam pocket(s).
(2) The ceiling height shall be taken as the average height
over slope.
(3) Spacing shall be measured along a horizontal projection
of the ceiling.
(4) Smooth ceiling spacing shall be permitted within beam
pocket(s) parallel to the beams.
(5) For beam depths less than or equal to 10 percent of the
ceiling height (0.1 H), spot-type detectors shall be located
with smooth ceiling spacing perpendicular to the beams.shall apply:
(a) Where beam spacing is equal to or greater than 40 percent
of the ceiling height (0.4 H), spot-type detectors
shall be located on the ceiling in each beam pocket.
(b) Where beam spacing is less than 40 percent of the
ceiling height (0.4 H), the following shall be permitted
for spot detectors:
i. Smooth ceiling spacing in the direction parallel to
the beams and at one-half smooth ceiling spacing
in the direction perpendicular to the beams
ii. Location of detectors either on the ceiling or on
the bottom of the beams
(3)*For beam pockets formed by intersecting beams, including
waffle or pan-type ceilings, the following shall apply:
(a) For beam depths less than 10 percent of the ceiling
height (0.1 H), spacing shall be in accordance with
17.7.3.2.4.2(1).
(b) For beam depths greater than or equal to 10 percent
of the ceiling height (0.1 H), spacing shall be in accordance
with 17.7.3.2.4.2(2).

結果 (中文) 1:

17.7.3.2.4.3* For sloping ceilings with beams running parallelup slope, the following shall apply:(1) Spot-type detector(s) shall be located on the ceiling withinbeam pocket(s).(2) The ceiling height shall be taken as the average heightover slope.(3) Spacing shall be measured along a horizontal projectionof the ceiling.(4) Smooth ceiling spacing shall be permitted within beampocket(s) parallel to the beams.(5) For beam depths less than or equal to 10 percent of theceiling height (0.1 H), spot-type detectors shall be locatedwith smooth ceiling spacing perpendicular to the beams.shall apply:(a) Where beam spacing is equal to or greater than 40 percentof the ceiling height (0.4 H), spot-type detectorsshall be located on the ceiling in each beam pocket.(b) Where beam spacing is less than 40 percent of theceiling height (0.4 H), the following shall be permittedfor spot detectors:i. Smooth ceiling spacing in the direction parallel tothe beams and at one-half smooth ceiling spacingin the direction perpendicular to the beamsii. Location of detectors either on the ceiling or onthe bottom of the beams(3)*For beam pockets formed by intersecting beams, includingwaffle or pan-type ceilings, the following shall apply:(a) For beam depths less than 10 percent of the ceilingheight (0.1 H), spacing shall be in accordance with17.7.3.2.4.2(1).(b) For beam depths greater than or equal to 10 percent天花板的高度 (0.1 H)，间距应按照与 17.7.3.2.4.2(2)。

結果 (中文) 3:

17.7.3.2.4.3 *倾斜的天花板与梁平行
坡，应适用下列：（1）
点型探测器（S）应位于天花板内
束口袋（S）。
（2）吊顶高度应为斜坡的平均高度

（3）。间距应在水平的天花板的投影
测量。
（4）光滑的天花板上的间距应在梁
允许口袋（S）平行的光束。
（5）梁的深度小于或等于百分之10的
天花板的高度（0.1 h），点型探测器应位于
光滑的天花板间距垂直于beams.shall申请：（一）在
梁间距大于或等于百分之40
天花板的高度（0.4 h），点型探测器
应位于每束口袋
天花板。（b）梁的间距小于百分之40的（0.4小时），以下应为现场探测器：即：在平行于方向平行的方向上，在方向垂直于光束的方向平行的方向上的光滑的天花板间距。探测器的位置，或在天花板上或在底部的光束（3）*束口袋交叉梁组成，包括
饼和锅型天花板，应适用下列：（一）
梁深度小于上限的
身高百分之10（0.1小时），间距应与
17.7.3.2.4.2按照（1）（b）。
梁深度大于或等于百分之10
天花板的高度（0.1 h），间距应符合
与17.7.3.2.4.2（2）。